KTM 1190 RC8 R, r.v. 2014
FRONT PADDOCK STAND
2 406 Kč
Sturdy tubular steel construction Tool for lifting the motorcycle at the fork legs Makes removal of the front wheel easier Tool for lifting the m...
CHARGER EU
24 075 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
OILFILTER SERVICE KIT
1 038 Kč
The oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
FRONT PADDOCK STAND
2 406 KčSturdy tubular steel construction Tool for lifting the motorcycle at the fork legs Makes removal of the front wheel easier Tool for lifting the m...
CHARGER EU
24 075 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
OILFILTER SERVICE KIT
1 038 KčThe oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
DEGREE DISK 360DEG - 1/2 INCH
Tool for tightening bolts with rotation angle (cylinder head nuts, conrod bearing bolts)
PLASTIGAUGE - MEASURING STRIP
Tool for measuring bearing play
EXTENSION TORQUE WRENCH
Bit for torque wrench, for tightening fittings to tightening torques (camshaft bearing support)
ADJUSTING PLATE FRONT
Tool for adjusting the valve timing on the front cylinder (cylinder 2)
ADJUSTING PLATE RAER
Tool for adjusting the valve timing on the rear cylinder (cylinder 1)
BUSHING EXTRACTOR
Tool for removing bearings from a housing
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
INTERN.BEAR.PULLER 28 MM
Tool for removing bearings from a housing
PULLER F. DAMPING RUBBER
Tool for changing the rubber dampers on the rear hub (aluminum rim)
PULLER CPL. F. IGNITION COVER
Tool for pulling off components (alternator cover)
PULLER F. COUNTERSHAFT DRIVE
Arms for puller, for pulling off components (primary gear, drive gear wheel of the balancer shaft)
RING F. COMB. SHAFT BEARING
Tool for pulling off components (inner bearing races from the balancer shaft)
PULLER
Tool for pulling off components (primary gear, drive gear wheel of the balancer shaft)
MOUNTING SLEEVE WD-RING
Tool for protecting components (installation of clutch cover)
FRAME SUPPORT
Support for frame when installing and removing engine
TRANSMISSION RACK CPL.
Attachment for floor jack, for lifting engine
VEHICLE STAND
Tool for lifting the motorcycle at the center
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
LIMIT PLUG GAUGE F.VALVE GUIDE
Tool for checking valve guides
VALVE SPRING TENSION APPLICAT.
Tool for installing and removing valves and valve springs
PRESS TOOL DM28
Tool for pressing components in (crankshaft support bearing)
PRES.SOCKET COUNTERSHAFT DRIVE
Tool for pressing in components (drive gear wheel of the balancer shaft)
COMBINATION PRESSURE PAD
Tool for pressing out components (drive gear wheel of the balancer shaft)
PRESSING TOOL D53 MAIN BEARING
Tool for pressing bearing shells in and out (main bearing)
BEARING RING F. PRESSING TOOL
Tool for pressing components in and out (main bearing)