KTM 1190 RC8 R, r.v. 2014
KTM OILFILTER SERVICE KIT
1 041 Kč
The oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
KTM ALARM SYSTEM BT
7 266 Kč
Plug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor An additional mounti...
KTM PLUG 22-42MM
242 Kč
Keeps water out of the silencer during cleaning. For inner-diameter of 22-42 mm
KTM CHARGER EU
24 149 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
KTM OILFILTER SERVICE KIT
1 041 KčThe oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
KTM ALARM SYSTEM BT
7 266 KčPlug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor An additional mounti...
KTM PLUG 22-42MM
242 KčKeeps water out of the silencer during cleaning. For inner-diameter of 22-42 mm
KTM CHARGER EU
24 149 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
KTM DIAGNOSTIC CABLE EXTENSION
Extension cables between VCI and diagnostic connector on the vehicle
KTM 12 V SUPPLY CABLE
External power supply for the VCI for vehicles without 12-V battery and for flashing of specific con...
KTM STYLUS
Stylus for input via the touch screen of the Getac F110 diagnostics tablet
KTM BREAKOUT-BOX
Box with connector board (without adapter and templates) for performing various electrical measureme...
KTM ADAPTER LC8
Adapter cable and template for performing various electrical measurements on the wiring harness
KTM CHARGER USA
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
KTM CHARGER GB
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
KTM CABLEPLUG OUTPINSET
Pinout kit including case and crimping pliers for repairing wiring harnesses or replacing the most c...
KTM BRAKE BLEEDER
Tool for servicing hydraulic brake systems
KTM BRAKE BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
KTM UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
KTM DEGREE DISK 360DEG - 1/2 INCH
Tool for tightening bolts with rotation angle (cylinder head nuts, conrod bearing bolts)
KTM PLASTIGAUGE - MEASURING STRIP
Tool for measuring bearing play
KTM EXTENSION TORQUE WRENCH
Bit for torque wrench, for tightening fittings to tightening torques (camshaft bearing support)
KTM ADJUSTING PLATE FRONT
Tool for adjusting the valve timing on the front cylinder (cylinder 2)
KTM ADJUSTING PLATE RAER
Tool for adjusting the valve timing on the rear cylinder (cylinder 1)
KTM BUSHING EXTRACTOR
Tool for removing bearings from a housing
KTM EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
KTM INTERN.BEAR.PULLER 28 MM
Tool for removing bearings from a housing
KTM PULLER F. DAMPING RUBBER
Tool for changing the rubber dampers on the rear hub (aluminum rim)
KTM PULLER CPL. F. IGNITION COVER
Tool for pulling off components (alternator cover)
KTM PULLER F. COUNTERSHAFT DRIVE
Arms for puller, for pulling off components (primary gear, drive gear wheel of the balancer shaft)
KTM RING F. COMB. SHAFT BEARING
Tool for pulling off components (inner bearing races from the balancer shaft)
KTM PULLER
Tool for pulling off components (primary gear, drive gear wheel of the balancer shaft)
KTM MOUNTING SLEEVE WD-RING
Tool for protecting components (installation of clutch cover)
KTM FRAME SUPPORT
Support for frame when installing and removing engine
KTM TRANSMISSION RACK CPL.
Attachment for floor jack, for lifting engine
KTM VEHICLE STAND
Tool for lifting the motorcycle at the center
