KTM, r.v. 2015
HANDLEBAR ENDS RIGHT+LEFT 05
387 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
MAGNETIC BOLT PAN, BLACK
387 Kč
Magnetic. Never lose a bolt again! Perfect for use in combination with the SX stand.
HANDLEBAR ENDS RIGHT+LEFT 05
387 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
MAGNETIC BOLT PAN, BLACK
387 KčMagnetic. Never lose a bolt again! Perfect for use in combination with the SX stand.
BRAKE BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
SUPPORT ENGINE BASE CPL.
Tool for securing the removed engine on the engine work stand
RETAIN. ARM F. ENG. WORK STAND
Tool for securing the removed engine on the engine work stand
CLUTCH HOLDER 85 SX 2003
Tool for holding components (clutch, primary gear wheel)
SPOKE TORK KEY
Torque wrench with various bits in the kit for tightening fittings to tightening torque (spokes)
ADJUSTING PLATE 85 SX 2003
Tool for checking the X dimension (piston protrusion) and the ignition setting
MAGNETIC PULLER M 27X1 KOKUSAN
Tool for pulling off components (rotor)
MOUNTING TOOL INNER RING NJ205
Tool for pulling off components (inner bearing race of crankshaft)
PROTECTION CAP CRANKSHAFT
Tool for protecting components (when disengaging the sections of the engine case)
GROUND PLATE
Anchor plate for screwing on to the pressing tool, for pressing the crankshaft together
PRESS OUT PLATE CRANKSHAFT
Tool for separating the crankshaft
PRESS. TOOL F. CRANKSHAFT
Sleeve with cover used as insert in the pressing tool for pressing the crankshaft together
HOLDING TOOL
Tool for assembling the fork legs (pulling out piston rod)
OPEN END WRENCH SW=22
Tool for disassembling and assembling the fork legs
VENTILATION & FILLING DEVICE
Tool for bleeding and filling dampers
PRE LOAD KEY 4681 STEEL
Tool for tensioning and releasing the springs (two units)
REGULATIVE TENS. PIN D=3
Tool for removing components (rebound damping adjustment of piston rod)
MOUNT. SLEEVE
Tool for mounting components (seal ring retainer on piston rod)
DRIVETRAIN KIT 85 SX
This drive kit consists of a 14 tooth front and a 46 tooth rear sprocket wheel, a Regina chain and m...
EXHAUST HARDWARE KIT MINI
The exhaust parts kit contains everything you need to repair your exhaust system.
GASKET SET CYL. 85 SX 13
The seal set contains all the seals you need to repair your cylinder.
CLUTCH KIT 105/85 SX 03-14
The clutch kit contains everything you need to repair your clutch.
FRONT WHEEL REP. KIT
The repair kit contains everything you need to repair the bearing support in your wheel.